Specialty Auto Parts For Sale - Crites Performance Parts

Randy
08-26-2014 10:52:38 AM CST
Ive seen the Clover leaf 64 Fairlane Fiberglass hood and was told they are benging made again.Is Crites doing them ? Your Glass quality is perfect and im hoping your the ones re-making the hoods.

Billy mnwild0827@yahoo.com
08-19-2014 2:06:31 PM CST

I have a '67 Galaxie 500 two door fastback. I'm looking for a fiberglass or metal teardrop hood. Not just the teardrop I'd like a one piece hood. Also, I'm looking for the interior rear divider (rear deck or rear shelf) that sits beneath the rear glass. Those are the final pieces I need to finish my project. Thanks for any help.

BobSS396 leftturn43@msn.com
08-10-2014 8:02:13 AM CST
WTB, 1959 Ford Custom parts (2DR sedan, body 64F). Mainly need interior trim, kick panels (same as Fairlane, Galaxie), rear window trim, upper body molding, vent window assemblies (may be same as Ranchero) and will consider complete doors or parts cars for the right $$.

MARK MVE@MHTC.NET
08-03-2014 4:17:27 PM CST
HAVE A 63 GALAXIE CONVERTIBLE FOR SALE IN WISCONSIN NO MOTOR OR TRANS...FRAME IS GOOD. A PARTS CAR WITH LOTS OF PARTS...HAVE OR ALL OF THE LONG TRIM, 90% OF IT IS GOOD. FLOOR PANS ARE GOOD BUT REAR QUARTERS AND TRUNK NEED REPLACING. WAS A 352 WITH AUTO. TOP MOTORS WORK AND ALL OF THE TOP BOWS ARE IN PLACE AND IN GOOD CONDITION. LOTS OF THE HARD TO FIND CONVERTIBLE TRIM PC'S ARE THERE. ALL GLASS IS IN IT AND GOOD. FRONT CLIP IS OFF.....ALSO HAVE RUNNING 289 WITH 3 SPD OVERDRIVE WITH 70K ON IT AND FOR SALE TOO. CAME OUT OF 63 GALAXIE 2DR SEDAN

Chris christopher.e.austin@uscg.mil
07-24-2014 7:37:30 AM CST
I know, Crites does Automatic based parts. However, I am going with a Hyd clutch set up on a 460 in Mustang. Anyone running this set up, particularly a Quick Time Bell with either a toploader or Jerico. I can find Slave brackets all day for the TKOs but not for the TL or Jerico.

OKIE getsaved@outlook;com
07-23-2014 11:09:53 AM CST

I have a 63 fairlane Sc, and am looking for 15inch rear steel wheels Like a TBolt would have I think they was 7 inch wide Question ie how to obtain these I been looking online ,I was told older cop cars or taxis from the early 70s work good but they are all crushed any help apreciated

Mark L. mlambert709@gmail.com
07-16-2014 7:24:07 PM CST

I have a 63 Meteor S33 that i would like to drop a 351W stroker in. Can i do it without modifying the shock towers and will the header listed here fit? I have power steering and will be using a C6 auto trans. Thanks,

Mark L.
07-16-2014 7:19:19 PM CST

I have a 63 Meteor S33 that i would like to drop a 351W stroker. Can i do it without modifying the shock towers and will the header listed here fit? I have power steering and will be using a C6 auto trans. Thanks,

Mark L.
07-16-2014 7:19:15 PM CST

70 Maverick wolf4lrrh@yahoo.com
07-16-2014 10:32:48 AM CST

Tried other headers and they "worked" with some help (aka hammering). The Crites set I use now work perfectly. This is a 351W in a 69 1/2 Maverick. Story is on Ford Muscle in Maverick section. Soon I'll be working on a 68 Cougar with a 460 using Crites headers also.

Brian K bbtorino@yahoo.com
06-26-2014 10:44:00 PM CST

Recently installed Crites Headers on my '76 Big Block Gran Torino, replacing Hooker Super Comps. PERFECT fit, from the port alignment to the clearance of every tube (I screwed up the paint in the pic). Even better, they lowered my ET by almost 2 tenths.

JimA
06-13-2014 11:14:48 AM CST
Has anyone tried to use the 460 T-bird headers on a '77-'79 Lincoln Coupe?

Larry thegoingthing@yahoo.com
05-26-2014 10:07:54 PM CST

Does anyone make a reproduction radio delete plate for a 66 Fairlane?

Bob Clymer Umbob51@yahoo.com
05-26-2014 9:19:49 PM CST
Hi everyone. Do any of you Ford Fox body lovers know where I can get Fiberglass doors for my 85 mustang gt? I have looked everywhere. Thanks for any feedback you can provide! Bob In Michigan

bill bsells2785@gmail.com
05-08-2014 12:50:36 PM CST

I see you offer a trunk lid for a 57 custom how about front fender?

darrell annettelewis28@yahoo.com
04-25-2014 4:57:41 PM CST
im looking for engine stands for a 429 torino 1970 or 1971 . can anyone please help

Glen gdsjr77@comcast.net
04-17-2014 4:29:47 PM CST
Hello, I have a 65 Falcon Futura hardtop. If I perform the shock tower conversion, will I still be able to perform a UCA (Shelby) drop? I can't tell from the photos? Thank you!

Norris norrissull129@gmail.com
04-16-2014 9:25:45 PM CST
65 Comet: I'm looking for fiberglass doors, decklid, bumpers, fenders and hood for my 65 Comet

Jim hipocomet@hotmail.com
04-16-2014 10:51:12 AM CST
66-67 Galaxie Big in/Big out Close Ratio Toploader for sale. 4 new gears, new 31 spline mainshaft, new cluster gear and a rebuild kit all from Dan Williams Toploaders. Cases were degreased, bead blasted and painted Cast Grey. All internal parts cleaned and degreased. Bolt in and go. Email for pics and price. Call 617-293-0359. Thanks, Jim

Glenn wireheadracing@gmail.com
04-06-2014 9:11:01 PM CST
going to put a 390FE with a T5 trans into a 1972 comet 4 dr. anyone have any suggestions on mtr mounts and trans mounts?

Bruce bruce56kit@hotmail.com
03-27-2014 2:52:59 AM CST
Does anyone know the weight of a : 65 Galaxie fiberglass front fender ? 65 Galaxie fiberglass hood ? 65 Galaxie fiberglass trunklid ?

Ken Anderson 62meteor@comcast.net
03-17-2014 5:47:38 AM CST
Hi, I am looking for motor mount kit for my 1962 Meteor. I am installing a 70-71 302. I have heard good things about Crites and want to buy them.

Jim Hughes jhughes484@aol.com
03-08-2014 6:51:21 PM CST
Hi, I am looking for a one piece front end for a 60 to 63 Falcon. New or used. I am unable to find one. I thought Crites may have one, but I don't see them listed. Please contact me if one is available. Jim Jhughes484@aol.com

Damian eduj64@gmail.com
02-24-2014 6:01:08 PM CST
I have a 1967 Galaxie 500. will a WTS 400M engine and C6 transmission setup pulled from a 1968 Mustang fit my car? Please help

PREV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 NEXT

TTWS