If you just made a post, click here to view it.

Michael Carnes   cargarage18@yahoo.com
10-30-2015 9:06:58 PM CST
I am in need of an aluminum front bumper,chrome rear bumper & a rubber floor mat for my 64 post fairlane if anyone has these or know where to get them please let me know.. thanks Michael carnes 270-866-3020.. I also have alot of left over parts for this car if somebody would want them.

Marty Dunn   mdunn@hcsheriff.gov
10-20-2015 6:07:58 PM CST

930 plus hours in saving this poor old car from the crusher so far and I estimate another 300 to go....The Sheriff's HEAT/Facebook

Marty Dunn   mdunn@hcsheriff.gov
10-20-2015 5:57:59 PM CST

Finally got the new front suspension from Control Freaks under the car and height about where I want it....

Scotty
10-03-2015 1:19:07 PM CST
I have a 65 Fairlane wagon and was wondering if I could cut the inner fender wells out. I have already installed a complete front end with coil overs and a new cross member, and removed the shock towers. I know I would have to run a piece of flat bar to bolt the top of the fenders to, but was wondering what else I might have to brace up.

Sam J
09-21-2015 8:21:38 AM CST
Building 64 HT. Has anyone used Crites, rear spring relocation kit? What is rear width, rim size,back spacing, etc... HELP!!!!

Carsten   c.tielke.ct@gmail.com
09-12-2015 7:25:18 PM CST
Hello! I am searching for a rear bumper cover for a 1968 Mercury Park Lane convertible. Does somebody can help me? Thanks Carsten

Rod Denning   rod69973@gmail.com
08-26-2015 9:22:23 AM CST

For sale 65 comet 7500.00 firm comes with extras contact me for info 814-833-3645 ask for Rod

Andrew
08-24-2015 1:06:53 PM CST
Hey all, I have a 1963 Fairlane, 2dr post for sale. I have installed a 351W with a C-4 trans, and a 9 in. rear-end. It does have disk brakes at all four corners, with new master cylinder. does have new ball joints and tie rod ends. It is a decent New Mexico body. Health issues prevent me from finishing this project any time soon, don't need to get rid of, but.... if any one is interested in finishing. 720-496-5726

Nwcat
08-11-2015 4:50:47 PM CST
Looking for fiberglass bumpers for a 1968 Galaxie fastback! Any leads are greatly appreciated 👍

John
07-24-2015 1:09:53 PM CST
looking to see if there is a torque box rebuild kit to buy for 64 falcon ranchero. I am located in WNY area. thanks

Douglas   ttmmer@earthlink.net
07-22-2015 8:54:25 PM CST
i need a conversion i have a 1960 ford fairland with the 6 motor i want a motor mount kit for a 429 is there such a conversion thanks i am in calif

chris   singberg@yahoo.com
07-14-2015 7:56:18 PM CST
wondering if you had any fiberglass items for a 62 mercury meteor s 33 looking for a front bumper

Terry Wharff   susankozlowski7@gmail.com
06-25-2015 2:18:11 PM CST
Looking for the air bonnet in aluminum for a dual quad carburetor setup. Apparently Crites isn't reproducing them anymore. Thank you. Reply to susankozlowski7@gmail.com.

Dan   dan6020@gmail.com
06-21-2015 12:38:49 PM CST
I have a 460 Ford with a C6 transmission do I need that metal plate in between the trans and the engine .

Ron Clemons   clemonsbrothers8955@gmail.com
06-12-2015 4:56:06 PM CST
Hi,I'm looking for a Radio and Clock deleat block off plates for a 1963 1\2 Ford Galaxie 500. Thank You So Much!

Dan
06-05-2015 12:56:02 PM CST
I have a 460 ford with C6 transmission there's a thin metal plate between the trans and the engine do I need it.

Don carroll   Donsuecarroll@sbcglobal.net
05-23-2015 6:37:45 AM CST
Looking for a rear bumper for 65 ford fairlane

Scott   Scott.caden@hotmail.com
05-07-2015 6:19:33 PM CST

Hello I bought the 72-79 Ford Torino motor mount kit for a 460 from crimes and I was just wondering if anyone has had to shim them to fit tight on the frame.my frame is four inches and the mounts are 4 1/4.

John   jwebbnc@gmail.com
04-25-2015 12:07:52 PM CST
Does anyone know how much weight a 64 Galaxie 500 will drop if the F/G doors, hood, trunk lid, bumpers and brackets are used? Thanks

Gary Warren   garysmach1@msn.com
04-24-2015 9:09:33 PM CST
Building a 351w with AFD cleveland aluminum heads and a c6 to put in a '57 fairlane. Anyone know if anyone manufactures headers for an application like this or if there is a way to modify an existing set of headers with minimal work? Thank you.

Mikey   mike.zinger@edmonton.ca
04-06-2015 10:13:07 AM CST
Trying to stuff a 460 into a 71 Torino. Yes I know it fits but....through a smoking deal I have a race ready motor with Motorsport heads and intake. Things a extremely tight because the new head is so tall. The exhaust bolt pattern is also different. Is it possible to get the wrap around headers made to match the Motorsport exhaust bolt pattern. Also the tighter to the block the better. Help me please

Bobby Gilbert   bobbygilbert@twc.com
03-24-2015 10:17:42 PM CST

Low riser setup 2x4 for sale

Bobby Gilbert   bobbygilbert@twc.com
03-24-2015 10:17:28 PM CST


Bobby Gilbert   bobbygilbert@twc.com
03-24-2015 10:17:23 PM CST


Bobby Gilbert   bobbygilbert@twc.com
03-24-2015 10:17:22 PM CST


PREV   1   2   3   4   5   6   7   8   9   10   11   12   13   14   15   16   17   18   19   20   21   22   23   24   25   26   NEXT









TTWS